[vacancy] Electrical Engineer - Maintenance for Kuwait
We are looking for Electrical Engineer (Maintenance) for a long term contract (12-24 months) for our Client, a European MNC, for their projects in Kuwait.
Candidate should be BE or Diploma in Electrical with relevant experience of 5 - 10 years in Power Transmission & Distribution sector. Candidate has to perfom preventive maintenance , emergency work , repair for installation type B65 - B95 - T65 - C65 - S105 - B105 and make retrofit, overhauling. At least 5 years experience on Areva / Alstom Equipments like Gas Insulated Substations / Switchgears (GIS) is a must.
Job Profile details are as follows:
1 - General Knowledge:
- Risks and means of prevention linked with handling/work at height/electrical current/use of pressurized tank/SF6 gas
- Principle of operation of GIS equipment
- Reading an assembly drawing
- Reading an installation drawing/a cable routing drawing
- Principle of operation of hydraulic mechanisms
- Principle of operation of Local Cubicle Control
- Principle of operation of Spring Operating Mechanism
- Principle of operation of Earthing Switch
- Operation's process on contaminated compartments
- Test Sheet and Reporting
2 – Standard maintenance
- M2 procedure
- M4 procedure with hydraulic mechanism
- M4 procedure with spring mechanism
3 – Main actions for M2 maintenance of GIS installation:
- Compartments Gas inspection :
· SF6 pressure measurement
· Moisture content : dew point , ppm value
· SF6% measurement
· Acidity and density checking
· SF6 Tightness checking
- Circuit Breaker inspection :
· tripping coil , motor , heater
· filling & bleeding : pump , rams, control piping
· Nitrogen pre-inflation ( accumulator ) : pressure rising and dropping
· Pressure switch thresholds : Pump , closing ( unlocking – locking ) , trip
· Check oil tank level, filter
· Check timing : open, close , tripping ...
- CT and VT checking :
· wiring connection and labeling
- Isolators and E/S mechanical inspection
· manual, electrical checking : open close
· Interlock checking
· Various inspections: heating, wiring connections, rod& shaft …
· Motor current measurement
- Functional test for local cubical
· Isolator. E/S, CB
· Hydraulic alarm and interlock
· Gas monitoring
4 - Mission on station in Service
- Control of safety CHECK-LIST
- Procedure for obtaining a work permit
- Evaluation of the condition of the equipment according of the number of cut-offs
- Dismantling, inspection and re-assembly of all the components using the special tools and according to the instructions.
- Inspection of equipment after dismantling following an incident
- Commissioning and specific test after intervention
- Material needs definition for a repair
5 - Specific Operations on a Major Failure
- Circuit Breaker, Disconnector, Earthing Switch, Other GIS devices:
· Knowledge of the lubrication procedure
· Removal and installation of the breaker pole from/into the Bay.
· Life Part removal from tank using special tools
· Commissioning and specific testing after major examination
· Location of Flashover
· Dismantling, inspection and re-assembly of the various Life Part components
· S02 Measures - Knowledge of the levels acceptance - Results interpretation
· Diagnostic of GIS internal parts
· Diagnosis after a flashover
- HYDRAULICS
· Detailed knowledge of the operation of Mechanisms
· Using the Special Tools remove from the cubicle the components to be overhauled
· Dismantling, inspection and re-assembly of all the components of the ram using the special tools and following the instructions
· Dismantling and installation of hydraulic pipe systems
· CH2, CH3 & CH4 Mechanisms: Dismantling, inspection and re-assembly of all the internal components using the special tools and following the instructions.
· Commissioning and specific testing after a major examination
· Troubleshooting
- SPRING MECHANISMS
· Knowledge of the operating principle
· Knowledge of the lubrication method
· Use of specific tools
· Knowledge of the measurement method on dashpot, roller play & over travel
· Adjustment of the breaker timing
· Dismantling, inspection evaluation of mechanical wear, re-assembling & adjustment
· Troubleshooting
If your profile matches our requirement, Please send your detailed updated CV in Word Format to epcengg@gmail.com along with following details for faster CV processing:
Current Location:
Current Salary:
Expected Salary:
Joining Time:
Please inform your Friends & Colleagues about this opening who fit our required profile and are worth recommending as per your opinion.
Thank You & Regards,
Team Aarvi
For regular updates on Job Openings in Oil & Gas, Power & Infrastructure:
__._,_.___
____
40000+ members and counting.
No Spam. No Ads. No Bull. Just plain job posts.
Join us, send a blank e-mail to: vacancy-subscribe@yahoogroups.com
For jobs in India, send e-mail to: vacancy-india-subscribe@yahoogroups.com
===================
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe
__,_._,___